home *** CD-ROM | disk | FTP | other *** search
/ Atari Mega Archive 1 / Atari Mega Archive - Volume 1.iso / misc / pwrspply.lzh / PWRSPPLY.TXT < prev   
Text File  |  1985-11-20  |  3KB  |  79 lines

  1.  
  2.                   All purpose 20V power supply modification
  3.                   -----------------------------------------
  4.  
  5.  
  6.       Here is a very quick and easy modification of a 12V power supply
  7. available at a Long Island electronics liquidator.  However, you can use
  8. this basic idea to modify any fixed power supply that uses any of the
  9. LM78xx series of chips to now work as a variable supply.  The heart of
  10. this project is the LM317T adjustible regulator.  You can pick these parts
  11. up at Radio Shack (except for the power supply itself) if you wish.
  12.  
  13.  
  14. Parts List:
  15. -----------
  16.  
  17.                   (1) 12V DC, 1.2 Amp Regulated Power Supply (TD626-2)
  18.                   (1) LM317T Adjustible Voltage Regulator
  19.                   (1) 5K ohm Potentiometer, Linear Taper
  20.                   (1) 330 ohm Resistor
  21.  
  22.                   24 Gauge Wire
  23.                   Black Tape
  24.  
  25.  
  26. Directions:
  27. -----------
  28.  
  29.       1) Get a SHARP exacto-knife and cut along the seam of the power
  30. supply several (thousand :-) ) times.  You may need a saw to cut through
  31. the corners.  I used a coping saw (it was availible)....
  32.  
  33.       2) When you cut through most of the plastic around each side of
  34. the power supply, try to pry it off with a flathead screwdriver.  Once you
  35. get the top off, pull back the foam and use a rubber band to hold it back
  36. on the top of the transformer while you work.
  37.  
  38.       3) Inside the power supply, find the fixed regulator chip.  Unscrew
  39. it from the rectangular heat sink.  Be careful not to lose the little
  40. plastic insulator between the chip and heat sink.  Yes, the white goo
  41. is messy :-)
  42.  
  43.       4) Cut the chip's leeds off at the base of the black part of the
  44. regulator.  You should have three metal "posts" sticking up from the
  45. ex-leeds of the 12 volt regulator.
  46.  
  47.       5) Take a look at the schematic included with this file.  Use 24
  48. gauge wire to solder this circuit together. Be sure to use black tape
  49. to insulate the 317's leeds and whatever exposed solder joints there are.
  50. A good "trick" is to insert the 330 ohm resistor between the two wires by
  51. using a wire-stripper in the middle of the wire to create a gap of copper
  52. wire.  Wind the resistor leeds around each exposed gap of copper.
  53.  
  54.       6) Flip the heat sink upside-down so the hole is on the opposite
  55. side.  Mount the 317 in that hole turned sideways.  Drill a hole in the
  56. top case for the potentiometer and don't forget the small hole for the
  57. little tab on the side sticking up on the pot!  Make sure you fit the pot
  58. on the left, next to the big capacitor, not on top of it!
  59.  
  60.       7) Put the cover back on and use thick TIGHT rubber bands to hold it
  61. shut.  Use a voltmeter and test it out.
  62.  
  63.  
  64. This particular transformer model can go up to 20V!  Don't ask me why it
  65. was so over-designed.....
  66.  
  67. In case you want to use another power supply that doesn't have an input
  68. voltage that goes up to 20V, you can calculate what resistor to use in
  69. place of the 330 ohm value with this formula:
  70.  
  71.                         R1 = 6250 / (Vout - 1.25)
  72.  
  73.  
  74. You can pick one up at:   Edlies Electronics
  75.                           2700 Hempstead Turnpike
  76.                           Levittown, NY 11756-1443
  77.                           1 800 645-4722
  78.                           NYS: 516 735-3330
  79.